206 Results: New & Used in Auto Body parts in Lake Macquarie Area, NSW

Vx ss fog lights good condition

Vx ss console for a under radio does open and close good condition

Bench seat for Mercedes Vito van. Price is negotiable as we have replaced the seat with drawers. It was a second row seat behind driver and passenger. Not sure if you could use it as a third row seat.

100 series Landcruiser front bumper used silver/grey

Genuine Toyota Yaris rubber floor mats. Excellent condition. Only 6 months old. New over $120. Cash and pickup only.

Tafe project that's been hanging in garage for 25 years Can't remember what year or model its off Welcome to inspect Pick up Windermere Park

No longer required, ba/bf ford falcon xr6 Ute drivers seat in good condition for age as pictured located Newcastle $250ono negotiable

Selling the original fuel tank for a PJ /PK Ranger.. came out of our 2008 PJ Ranger, comes with Guard plate. There are no issues with this fuel tank, we have just upgraded to a long range fuel tank. Call if interested, I will not be replying to emails or messages.

Genuine ford tonneau cover Less than 6 months old Comes with fitting kit In good condition

Xy front upper windscreen cut. Rusty with usable sections and good headlining retaining trim. Postage $30 after cutting down to 103cm for auspost.

Xy sedan upper passenger rear quarter panel rust cut. Good for the lower roof pillar section wear vinyl tops rust them out. Willing to cut down for auspost. Postage $30 most area's.

Xy sedan fuel cap cut section. Good for repair panel or make a gt wall art out of it for the man cave. Postage $25 most area's.

Xy sedan window glass set, in good condition for their age. Postage most area's $40.

1950 Lucas King of the road, headlight bucket with side mount bracket and wiring harness, good condition $50 can post at cost

X3 gear sticks two with bases $20each Under body filler neck cover $20 Gti seats $300 or swaps for good condition Sierra seats Wt bonnet $150 has dents and little rust Support bar rust in usual spot $100 Above Door frame $50 Interior filler neck cover for swb $20

in good nick original cover came off a 2014 fgx ute no rips or major defects

Original Holden 62/64 EH EJ rear bumper bar and brackets in 3 pieces,some surface rust and one centre dent $150 location Swansea nsw could possibly post but would be expensive

Suit earlier JM model 2004 to 2009. Original factory part. Roller type cargo screen. 3 individual rollers plus retainer hooks. Never been used. Came on the vehicle when bought new. Been stored in plastic bag since day of purchase.

Selling my rear setup and having a clean up Arb classic canopy in good condition all fitting hardware $1700ono Tub and bumper make me an offer, panel damage on passenger side few bumps inside, tail lights in good condition with stedi reverse lights Located Newcastle nsw Will swap for alloy tray with cash either way depending on type of tray

2 VH commodores White/primer one is a 6 cyl sl. Good honest country car with minimal rust, rear quarters have had small amount of rust cut out, one side has been repaired the other side has new piece ready to go in. I purchased this pretty much the way it is. Underneath has been under bodied. I’ve been collecting parts for the build & chipping away at it here & there it’s almost ready for panel & paint. Green one was a 253 slx, major structural rust in my opinion beyond repair. I purchased this

Toyota Hilux side step in good condition off 2018 model

Selling a Huracan Fabrication tailgate storage unit to fit a******2016 Isuzu D-MAX. The unit is still basically brand new, in perfect condition and even had the top of the unit professionally lined with Rhino Linings to improve durability of the top coating. Can no longer seem to find the self tapping screw fittings used to secure the unit to the tailgate but these can be bought at any hardware store. However, I have reached out and have a brand new cardboard template from Huracan so this unit

Head gasket set for Holden commodore******2000 Unopened Never used

Selling these two AE86 rolling Shell's. Not looking to part out. Both will be sold as a rolling shell with doors and some glass. Both have clean tags and with alot of effort could be put on the road again if desired. Would prefer to see both go together but will separate if needed. Can negotiate some parts for extra cost but won't sell separately. they both have rust that will need repairing, my plan was to use cuts from one to repair the other. or you could buy the new pressed metal panels